網站首頁 >> 技術文檔 >> 熒光磁粉探傷機定期整機檢定項目
熒光磁粉探傷機定期整機檢定項目
熒光磁粉探傷機作為質量檢測設備,按計量技術規范規定,磁粉探傷機需一年一檢,進行靈敏度校準。
序號 |
類目 |
檢修事項 |
1 |
導電性檢測 |
磁粉探傷機整機各電纜連接接頭接觸導電是否良好 |
導電電極導電性調校 | ||
2 |
氣動件檢測 |
磁粉探傷機通電電極夾緊、松開靈活度調校 |
3 |
PLC程序 |
磁粉探傷機自動程序、手動程序操作運行檢查調校 |
4 |
磁化電流 |
磁粉探傷機周向電流、縱向電流連續可調,且能實際顯示。 |
5 |
剩磁強度 |
將已磁化的工件進行退磁,通過高斯計測量剩余磁感應強度小于0.2mT。 |
6 |
觀察條件 |
熒光磁粉探傷機在紫外光照下,被測工件表面距紫外光源380mm處不小于1.0mW/cm2。 |
7 |
安全性能 |
電源端與保護接線端之間的絕緣電阻應不小于2MΩ,測試電壓為500V。 |
電源端與保護接線端之間應能耐受1.5KV(50HZ交流有效值)的電壓,保持時間1min,應無飛弧和擊穿現象。 | ||
8 |
綜合靈敏度 |
磁粉探傷機的綜合靈敏度用試片及實體裂紋試件進行實際檢測在周、縱向電流實際值時檢測,清晰顯示。 |
一臺好的探傷機設備,如果不注意平時預防性地維護保養工作,防止因殘留污垢、缺乏潤滑劑、螺絲松動等問題而造成設備過早損壞或頻繁發生故障,會(huì )使設備壽命大打折扣,甚至使整個設備癱瘓。
為保證設備在完好狀態下工作,最大限度地減少停機損失,宏旭探傷機建議請制定設備日常和定期維護保養制度及維護周期,并由經過培訓的專門人員對熒光磁粉探傷機進行維護保養。
轉載請注明轉載自:射陽宏旭探傷機制造有限公司http://www.coinbucks.top。