網站首頁 >> 采購指南 >> 磁粉探傷儀操作規程
磁粉探傷儀操作規程
磁粉探傷儀操作規程
一、使用磁粉探傷儀前準備工作
1、操作者必須經過磁粉探傷培訓合格后持證上崗,勞保用品穿戴齊全、整齊。
2、詳細檢查磁粉探傷儀各部位是否良好,各部位接線是否牢靠。
3、磁粉為非熒光干法黑磁粉,80-160 目。
二、磁粉探傷儀作業準備
1、閉合磁粉探傷儀電源開關。
2、打開 磁粉探傷儀“電源開關” ,電源接通,電源指示紅燈亮。
3、詳細檢查磁粉探傷儀各表、按鈕工作是否正常。
4、檢查干粉噴撒器噴撒狀況,有無堵塞。
5、靈敏度及提升力試驗符合標準要求。
三、 探傷操作
1、將磁粉探傷儀控制開關全部置于“開”的位置。
2、均勻噴撒磁粉并磁化,磁軛移動過程中,應保證縱、橫兩個方向都能分別磁化,無漏探。
3、 作業時,要注意安全,工件吊運過程中,不得野蠻操作,防止造成人身事故。
四、 探傷作業結束
1、關斷磁粉探傷儀控制面板開關。
2、關斷磁粉探傷儀總電源開關。
五、磁粉探傷儀維護保養
1、 操作人員應詳細了解磁粉探傷儀性能特點,熟悉磁粉探傷儀各種按鈕 作用,操作方法和注意事項,嚴格按磁粉探傷儀說明書操作。
2、操作人員每天工作前須檢查磁粉探傷儀電流和電壓表、提升力。
3、磁粉探傷儀不能空載,以防電流過大燒壞儀器。
4、 馬蹄不允許硬砸,以防開叉后探傷靈敏度達不到要求。
5、磁粉探傷儀每天使用完畢,將電源開關關閉并將電源拔掉。
6、 磁粉探傷儀每次使用后,應將打結的連接電纜整理順暢。
7、磁粉探傷儀每次使用完畢,應將磁粉探傷儀連接電纜、馬蹄磁軛的外表清潔干凈,并整齊放置于規定。
射陽宏旭探傷機制造有限公司 http://www.coinbucks.top 是專業生產磁粉探傷儀,磁粉探傷機,退磁機的骨干企業,產品技術科技含量不斷提高,綜合實力雄厚,歡迎新老客戶前來合作。